OpenCores
no use no use 1/1 no use no use
XC5VLX110T -orpsocv2
by mazhengfei on Mar 12, 2018
mazhengfei
Posts: 2
Joined: Nov 3, 2017
Last seen: Aug 5, 2018
Dear all
I'm using the or1200 processor on FPGA right now, but I've had a lot of problems
The problem is focused on the loading board, when I send the data (orpmon/) to the board. Here is my logs of the questions.Thanks !

1.The first question
There are many reading errors here, although it is best to be ready for the JTAG chain at the end
-------------------------------------------------------------------------------------------------
openrisc@openrisc-VirtualBox:~/BSD$ sudo adv_jtag_bridge -b /home/openrisc/BSD xpc_usb
[sudo] password for openrisc:
Found Xilinx Platform Cable USB (DLC9)
Found Xilinx Platform Cable USB (DLC9)
XPC USB driver opening cable
firmware version = 0x0517 (1303)
cable CPLD version = 0x0012 (18)
Enumerating JTAG chain...

Devices on JTAG chain:
Index Name ID Code IR Length
----------------------------------------------------------------
0: XC5VLX110T 0xA2AD6093 10
1: XCCACE 0x0A001093 8
2: xc95144xl 0x59608093 8
3: XCF32P 0xF5059093 16
4: XCF32P 0xF5059093 16

Target device 0, JTAG ID = 0xa2ad6093
Xilinx IDCODE, assuming internal BSCAN mode
(using USER1 instead of DEBUG TAP command)
IDCODE sanity test passed, chain OK!
JSP server listening on host openrisc-VirtualBox (0.0.0.0), port 9944, address family IPv4
JSP server thread running!
Burst read timed out.
Retry count exceeded in burst read!
ERROR reading DCR 0 at startup! 'max retries'
Burst read timed out.
Retry count exceeded in burst read!
ERROR reading DCR 1 at startup! 'max retries'
Burst read timed out.
Retry count exceeded in burst read!
ERROR reading DCR 2 at startup! 'max retries'
Burst read timed out.
Retry count exceeded in burst read!
ERROR reading DCR 3 at startup! 'max retries'
Burst read timed out.
Retry count exceeded in burst read!
ERROR reading DCR 4 at startup! 'max retries'
Burst read timed out.
Retry count exceeded in burst read!
ERROR reading DCR 5 at startup! 'max retries'
Burst read timed out.
Retry count exceeded in burst read!
ERROR reading DCR 6 at startup! 'max retries'
Burst read timed out.
Retry count exceeded in burst read!
ERROR reading DCR 7 at startup! 'max retries'
No watchpoint hardware found, HWP server not starting
JTAG bridge ready!
----------------------------------------------------------------------------------------------------------------
2.The second question
And,the JTAG was exited the connection when I executed this command.
-----------------------------------------------------------------------------------
openrisc@openrisc-VirtualBox:~$ or32-elf-gdb
Building automata... done, num uncovered: 0/216.
Parsing operands data... done.
GNU gdb (OpenRISC 32-bit toolchain for or32-elf (built 20111014)) 7.2-or32-1.0rc3
Copyright (C) 2010 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later ;" target="_blank">http://gnu.org/licenses/gpl.html>;
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law. Type "show copying"
and "show warranty" for details.
This GDB was configured as "--host=i686-pc-linux-gnu --target=or32-elf".
For bug reporting instructions, please see:
;." target="_blank">http://www.opencores.org/>;.
(gdb) target remote:9999
Remote debugging using :9999
Remote communication error. Target disconnected.: Connection reset by peer.
(gdb)
-----------------------------------------------------------------------------------------

Burst read timed out.
Retry count exceeded in burst read!
CRC ERROR! match bit after write is 0 (computed CRC 0x174b23f1)Retry count exceeded! Abort!

openrisc@openrisc-VirtualBox:~/BSD$
--------------------------------------------------------------------------------------------------------
3.The third question
Neither the CPU nor the sdram detected it at the time of self-testing
-----------------------------------------------------------------------------------------------------------
openrisc@openrisc-VirtualBox:~/BSD$ sudo adv_jtag_bridge -b /home/openrisc/BSD -t xpc_usb
Found Xilinx Platform Cable USB (DLC9)
Found Xilinx Platform Cable USB (DLC9)
XPC USB driver opening cable
firmware version = 0x0517 (1303)
cable CPLD version = 0x0012 (18)
Enumerating JTAG chain...

Devices on JTAG chain:
Index Name ID Code IR Length
----------------------------------------------------------------
0: XC5VLX110T 0xA2AD6093 10
1: XCCACE 0x0A001093 8
2: xc95144xl 0x59608093 8
3: XCF32P 0xF5059093 16
4: XCF32P 0xF5059093 16

Target device 0, JTAG ID = 0xa2ad6093
Xilinx IDCODE, assuming internal BSCAN mode
(using USER1 instead of DEBUG TAP command)
IDCODE sanity test passed, chain OK!
*** Doing self-test ***
Stall or1k - or1k is not stalled!
Self-test FAILED *** Bailing out!
openrisc@openrisc-VirtualBox:~/BSD$
--------------------------------------------------------------------------------------------------------
Thank you very much for your help,
Zengfeima
RE: XC5VLX110T -orpsocv2
by zzsz on Apr 6, 2018
zzsz
Posts: 3
Joined: Mar 11, 2018
Last seen: Aug 27, 2018
are you chinese? have you solve this problem?
RE: XC5VLX110T -orpsocv2
by zzsz on Apr 6, 2018
zzsz
Posts: 3
Joined: Mar 11, 2018
Last seen: Aug 27, 2018
hello:
I want you ask that have you solve the problem?

good luck!

ZZSZ
RE: XC5VLX110T -orpsocv2
by mazhengfei on Apr 9, 2018
mazhengfei
Posts: 2
Joined: Nov 3, 2017
Last seen: Aug 5, 2018
Hi,

Thank you for your concern! I'm from Chengdu, China, and I haven't completely solved this problem, because I've been so busy lately. I'm going to get this done next month or rebuild a system with mor1kx. Excuse me, if you have any good ideas, maybe we can try together. Are you from China, too? Maybe we can talk about it!

no use no use 1/1 no use no use
© copyright 1999-2023 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.