Subversion Repositories spacewiresystemc

// (C) 2001-2017 Intel Corporation. All rights reserved.

// Your use of Intel Corporation's design tools, logic functions and other 

// software and tools, and its AMPP partner logic functions, and any output 

// files from any of the foregoing (including device programming or simulation 

// files), and any associated documentation or information are expressly subject 

// to the terms and conditions of the Intel Program License Subscription 

// Agreement, Intel FPGA IP License Agreement, or other applicable 

// license agreement, including, without limitation, that your use is for the 

// sole purpose of programming logic devices manufactured by Intel and sold by 

// Intel or its authorized distributors.  Please refer to the applicable 

// agreement for further details.

// ******************************************************************************************************************************** 

// File name: acv_hard_memphy.v

// This file instantiates all the main components of the PHY. 

// ******************************************************************************************************************************** 

`timescale 1 ps / 1 ps

module hps_sdram_p0_acv_hard_memphy (

        global_reset_n,

        soft_reset_n,

        ctl_reset_n,

        ctl_reset_export_n,

    afi_reset_n,

        pll_locked,

        oct_ctl_rs_value,

        oct_ctl_rt_value,

        afi_addr,

        afi_ba,

        afi_cke,

        afi_cs_n,

        afi_ras_n,

        afi_we_n,

        afi_cas_n,

        afi_rst_n,

        afi_odt,

        afi_mem_clk_disable,

        afi_dqs_burst,

        afi_wdata_valid,

        afi_wdata,

        afi_dm,

        afi_rdata,

        afi_rdata_en,

        afi_rdata_en_full,

        afi_rdata_valid,

        afi_wlat,

        afi_rlat,

        afi_cal_success,

        afi_cal_fail,

        avl_read,

        avl_write,

        avl_address,

        avl_writedata,

        avl_waitrequest,

        avl_readdata,

        cfg_addlat,

        cfg_bankaddrwidth,

        cfg_caswrlat,

        cfg_coladdrwidth,

        cfg_csaddrwidth,

        cfg_devicewidth,

        cfg_dramconfig,

        cfg_interfacewidth,

        cfg_rowaddrwidth,

        cfg_tcl,

        cfg_tmrd,

        cfg_trefi,

        cfg_trfc,

        cfg_twr,

        io_intaddrdout,

        io_intbadout,

        io_intcasndout,

        io_intckdout,

        io_intckedout,

        io_intckndout,

        io_intcsndout,

        io_intdmdout,

        io_intdqdin,

        io_intdqdout,

        io_intdqoe,

        io_intdqsbdout,

        io_intdqsboe,

        io_intdqsdout,

        io_intdqslogicdqsena,

        io_intdqslogicfiforeset,

        io_intdqslogicincrdataen,

        io_intdqslogicincwrptr,

        io_intdqslogicoct,

        io_intdqslogicrdatavalid,

        io_intdqslogicreadlatency,

        io_intdqsoe,

        io_intodtdout,

        io_intrasndout,

        io_intresetndout,

        io_intwendout,

        io_intafirlat,

        io_intafiwlat,

        io_intaficalfail,

        io_intaficalsuccess,

        mem_a,

        mem_ba,

        mem_cs_n,

        mem_cke,

        mem_odt,

        mem_we_n,

        mem_ras_n,

        mem_cas_n,

        mem_reset_n,

        mem_dq,

        mem_dm,

        mem_ck,

        mem_ck_n,

        mem_dqs,

        mem_dqs_n,

        reset_n_scc_clk,

        reset_n_avl_clk,

        scc_data,

        scc_dqs_ena,

        scc_dqs_io_ena,

        scc_dq_ena,

        scc_dm_ena,

        scc_upd,

        capture_strobe_tracking,

        phy_clk,

        ctl_clk,

        phy_reset_n,

        pll_afi_clk,

        pll_afi_half_clk,

        pll_addr_cmd_clk,

        pll_mem_clk,

        pll_mem_phy_clk,

        pll_afi_phy_clk,

        pll_avl_phy_clk,

        pll_write_clk,

        pll_write_clk_pre_phy_clk,

        pll_dqs_ena_clk,

        seq_clk,

        pll_avl_clk,

        pll_config_clk,

        dll_clk,

        dll_pll_locked,

        dll_phy_delayctrl

);

// ******************************************************************************************************************************** 

// BEGIN PARAMETER SECTION

// All parameters default to "" will have their values passed in from higher level wrapper with the controller and driver 

parameter DEVICE_FAMILY = "";

parameter IS_HHP_HPS = "false";

// On-chip termination

parameter OCT_SERIES_TERM_CONTROL_WIDTH   = "";

parameter OCT_PARALLEL_TERM_CONTROL_WIDTH = "";

// PHY-Memory Interface

// Memory device specific parameters, they are set according to the memory spec

parameter MEM_ADDRESS_WIDTH     = "";

parameter MEM_BANK_WIDTH        = "";

parameter MEM_IF_CS_WIDTH = "";

parameter MEM_CLK_EN_WIDTH      = "";

parameter MEM_CK_WIDTH          = "";

parameter MEM_ODT_WIDTH         = "";

parameter MEM_DQS_WIDTH         = "";

parameter MEM_DM_WIDTH          = "";

parameter MEM_CONTROL_WIDTH     = "";

parameter MEM_DQ_WIDTH          = "";

parameter MEM_READ_DQS_WIDTH    = "";

parameter MEM_WRITE_DQS_WIDTH   = "";

// PHY-Controller (AFI) Interface

// The AFI interface widths are derived from the memory interface widths based on full/half rate operations

// The calculations are done on higher level wrapper

// DLL Interface

// The DLL delay output control is always 6 bits for current existing devices

parameter DLL_DELAY_CTRL_WIDTH  = "";

parameter MR1_ODS               = "";

parameter MR1_RTT               = "";

parameter MR2_RTT_WR            = "";

parameter TB_PROTOCOL        = "";

parameter TB_MEM_CLK_FREQ    = "";

parameter TB_RATE            = "";

parameter TB_MEM_DQ_WIDTH    = "";

parameter TB_MEM_DQS_WIDTH   = "";

parameter TB_PLL_DLL_MASTER  = "";

parameter FAST_SIM_MODEL = "";

parameter FAST_SIM_CALIBRATION = "";

// Width of the calibration status register used to control calibration skipping.

parameter CALIB_REG_WIDTH = "";

parameter AC_ROM_INIT_FILE_NAME = "";

parameter INST_ROM_INIT_FILE_NAME = "";

// The number of AFI Resets to generate

localparam NUM_AFI_RESET = 4;

// Addr/cmd clock phase

localparam ADC_PHASE_SETTING = 0;

localparam ADC_INVERT_PHASE = "true";

// END PARAMETER SECTION

// ******************************************************************************************************************************** 

// ******************************************************************************************************************************** 

// BEGIN PORT SECTION

//  Reset Interface

input   global_reset_n;         // Resets (active-low) the whole system (all PHY logic + PLL)

input   soft_reset_n;           // Resets (active-low) PHY logic only, PLL is NOT reset

input   pll_locked;                     // Indicates that PLL is locked

output  ctl_reset_n;            // Asynchronously asserted and synchronously de-asserted on ctl_clk domain

output  ctl_reset_export_n;             // Asynchronously asserted and synchronously de-asserted on ctl_clk domain

output  afi_reset_n;            // Asynchronously asserted and synchronously de-asserted on afi_clk domain

input   [OCT_SERIES_TERM_CONTROL_WIDTH-1:0]    oct_ctl_rs_value;

input   [OCT_PARALLEL_TERM_CONTROL_WIDTH-1:0]  oct_ctl_rt_value;

// PHY-Controller Interface, AFI 2.0

// Control Interface

input  [19:0]  afi_addr;

input   [2:0]  afi_ba;

input   [1:0]  afi_cke;

input   [1:0]  afi_cs_n;

input   [0:0]  afi_cas_n;

input   [1:0]  afi_odt;

input   [0:0]  afi_ras_n;

input   [0:0]  afi_we_n;

input   [0:0]  afi_rst_n;

input   [0:0]  afi_mem_clk_disable;

input   [4:0]  afi_dqs_burst;

output  [3:0]  afi_wlat;

output  [4:0]  afi_rlat;

// Write data interface

input  [79:0]  afi_wdata;              // write data

input   [4:0]  afi_wdata_valid;          // write data valid, used to maintain write latency required by protocol spec

input   [9:0]  afi_dm;             // write data mask

// Read data interface

output [79:0]  afi_rdata;              // read data                

input   [4:0]  afi_rdata_en;       // read enable, used to maintain the read latency calibrated by PHY

input   [4:0]  afi_rdata_en_full;  // read enable full burst, used to create DQS enable

output  [0:0]  afi_rdata_valid;    // read data valid

// Status interface

output                                afi_cal_success;    // calibration success

output                                afi_cal_fail;       // calibration failure

// Avalon interface to the sequencer

input   [15:0]  avl_address; //MarkW TODO: the sequencer only uses 13 bits

input           avl_read;

output  [31:0]  avl_readdata;

output          avl_waitrequest;

input           avl_write;

input   [31:0]  avl_writedata;

// Configuration interface to the memory controller

input    [7:0]  cfg_addlat;

input    [7:0]  cfg_bankaddrwidth;

input    [7:0]  cfg_caswrlat;

input    [7:0]  cfg_coladdrwidth;

input    [7:0]  cfg_csaddrwidth;

input    [7:0]  cfg_devicewidth;

input   [23:0]  cfg_dramconfig;

input    [7:0]  cfg_interfacewidth;

input    [7:0]  cfg_rowaddrwidth;

input    [7:0]  cfg_tcl;

input    [7:0]  cfg_tmrd;

input   [15:0]  cfg_trefi;

input    [7:0]  cfg_trfc;

input    [7:0]  cfg_twr;

//  IO/bypass interface to the core (or soft controller)

input   [63:0]  io_intaddrdout;

input   [11:0]  io_intbadout;

input    [3:0]  io_intcasndout;

input    [3:0]  io_intckdout;

input    [7:0]  io_intckedout;

input    [3:0]  io_intckndout;

input    [7:0]  io_intcsndout;

input   [19:0]  io_intdmdout;

output [179:0]  io_intdqdin;

input  [179:0]  io_intdqdout;

input   [89:0]  io_intdqoe;

input   [19:0]  io_intdqsbdout;

input    [9:0]  io_intdqsboe;

input   [19:0]  io_intdqsdout;

input    [9:0]  io_intdqslogicdqsena;

input    [4:0]  io_intdqslogicfiforeset;

input    [9:0]  io_intdqslogicincrdataen;

input    [9:0]  io_intdqslogicincwrptr;

input    [9:0]  io_intdqslogicoct;

output   [4:0]  io_intdqslogicrdatavalid;

input   [24:0]  io_intdqslogicreadlatency;

input    [9:0]  io_intdqsoe;

input    [7:0]  io_intodtdout;

input    [3:0]  io_intrasndout;

input    [3:0]  io_intresetndout;

input    [3:0]  io_intwendout;

output   [4:0]  io_intafirlat;

output   [3:0]  io_intafiwlat;

output          io_intaficalfail;

output          io_intaficalsuccess;

// PHY-Memory Interface

output  [MEM_ADDRESS_WIDTH-1:0]      mem_a;

output  [MEM_BANK_WIDTH-1:0]         mem_ba;

output  [MEM_IF_CS_WIDTH-1:0]  mem_cs_n;

output  [MEM_CLK_EN_WIDTH-1:0]       mem_cke;

output  [MEM_ODT_WIDTH-1:0]          mem_odt;

output  [MEM_CONTROL_WIDTH-1:0]      mem_we_n;

output  [MEM_CONTROL_WIDTH-1:0]      mem_ras_n;

output  [MEM_CONTROL_WIDTH-1:0]      mem_cas_n;

output                               mem_reset_n;

inout   [MEM_DQ_WIDTH-1:0]           mem_dq;

output  [MEM_DM_WIDTH-1:0]           mem_dm;

output  [MEM_CK_WIDTH-1:0]           mem_ck;

output  [MEM_CK_WIDTH-1:0]           mem_ck_n;

inout   [MEM_DQS_WIDTH-1:0]          mem_dqs;

inout   [MEM_DQS_WIDTH-1:0]          mem_dqs_n;

output  reset_n_scc_clk;

output  reset_n_avl_clk;

// Scan chain configuration manager interface

input                              scc_data;

input    [MEM_READ_DQS_WIDTH-1:0]  scc_dqs_ena;

input    [MEM_READ_DQS_WIDTH-1:0]  scc_dqs_io_ena;

input          [MEM_DQ_WIDTH-1:0]  scc_dq_ena;

input          [MEM_DM_WIDTH-1:0]  scc_dm_ena;

input                       [0:0]  scc_upd;

output   [MEM_READ_DQS_WIDTH-1:0]  capture_strobe_tracking;

output  phy_clk;

output  ctl_clk;

output  phy_reset_n;

// PLL Interface

input  pll_afi_clk;       // clocks AFI interface logic

input  pll_afi_half_clk;        // 

input  pll_addr_cmd_clk;  // clocks address/command DDIO

input  pll_mem_clk;       // output clock to memory

input  pll_write_clk;     // clocks write data DDIO

input   pll_write_clk_pre_phy_clk;

input  pll_dqs_ena_clk;

input  seq_clk;

input  pll_avl_clk;

input  pll_config_clk;

input pll_mem_phy_clk;

input pll_afi_phy_clk;

input pll_avl_phy_clk;

// DLL Interface

output  dll_clk;

output  dll_pll_locked;

input   [DLL_DELAY_CTRL_WIDTH-1:0]  dll_phy_delayctrl;   // dll output used to control the input DQS phase shift

// END PARAMETER SECTION

// ******************************************************************************************************************************** 

wire  [179:0]  ddio_phy_dqdin;

wire    [4:0]  ddio_phy_dqslogic_rdatavalid;

wire   [63:0]  phy_ddio_address;

wire   [11:0]  phy_ddio_bank;

wire    [3:0]  phy_ddio_cas_n;

wire    [3:0]  phy_ddio_ck;

wire    [7:0]  phy_ddio_cke;

wire    [3:0]  phy_ddio_ck_n;

wire    [7:0]  phy_ddio_cs_n;

wire   [19:0]  phy_ddio_dmdout;

wire  [179:0]  phy_ddio_dqdout;

wire   [89:0]  phy_ddio_dqoe;

wire    [9:0]  phy_ddio_dqsb_oe;

wire    [9:0]  phy_ddio_dqslogic_dqsena;

wire    [4:0]  phy_ddio_dqslogic_fiforeset;

wire    [4:0]  phy_ddio_dqslogic_aclr_pstamble;

wire    [4:0]  phy_ddio_dqslogic_aclr_fifoctrl;

wire    [9:0]  phy_ddio_dqslogic_incrdataen;

wire    [9:0]  phy_ddio_dqslogic_incwrptr;

wire    [9:0]  phy_ddio_dqslogic_oct;

wire   [24:0]  phy_ddio_dqslogic_readlatency;

wire    [9:0]  phy_ddio_dqs_oe;

wire    [19:0]  phy_ddio_dqs_dout;

wire    [7:0]  phy_ddio_odt;

wire    [3:0]  phy_ddio_ras_n;

wire    [3:0]  phy_ddio_reset_n;

wire    [3:0]  phy_ddio_we_n;

wire    read_capture_clk;

wire    [NUM_AFI_RESET-1:0] reset_n_afi_clk;

wire    reset_n_addr_cmd_clk;

wire    reset_n_seq_clk;

wire    reset_n_scc_clk;

wire    reset_n_avl_clk;

wire    reset_n_resync_clk;

localparam SKIP_CALIBRATION_STEPS = 7'b1111111;

localparam CALIBRATION_STEPS = SKIP_CALIBRATION_STEPS;

localparam SKIP_MEM_INIT = 1'b1;

localparam SEQ_CALIB_INIT = {CALIBRATION_STEPS, SKIP_MEM_INIT};

generate

if (IS_HHP_HPS != "true") begin

        reg [CALIB_REG_WIDTH-1:0] seq_calib_init_reg /* synthesis syn_noprune syn_preserve = 1 */;

        // Initialization of the sequencer status register. This register

        // is preserved in the netlist so that it can be forced during simulation

        always @(posedge pll_afi_clk)

                `ifdef SYNTH_FOR_SIM

                `else

                //synthesis translate_off

                `endif

                seq_calib_init_reg <= SEQ_CALIB_INIT;

                `ifdef SYNTH_FOR_SIM

                `else

                //synthesis translate_on

                //synthesis read_comments_as_HDL on

                `endif

                // seq_calib_init_reg <= {CALIB_REG_WIDTH{1'b0}};

                `ifdef SYNTH_FOR_SIM

                `else

                // synthesis read_comments_as_HDL off

                `endif

end

endgenerate

// ******************************************************************************************************************************** 

// The reset scheme used in the UNIPHY is asynchronous assert and synchronous de-assert

// The reset block has 2 main functionalities:

// 1. Keep all the PHY logic in reset state until after the PLL is locked

// 2. Synchronize the reset to each clock domain 

// ******************************************************************************************************************************** 

generate

if (IS_HHP_HPS != "true") begin

        hps_sdram_p0_reset      ureset(

                .pll_afi_clk                            (pll_afi_clk),

                .pll_addr_cmd_clk                       (pll_addr_cmd_clk),

                .pll_dqs_ena_clk                        (pll_dqs_ena_clk),

                .seq_clk                                        (seq_clk),

                .pll_avl_clk                            (pll_avl_clk),

                .scc_clk                                        (pll_config_clk),

                .reset_n_scc_clk                        (reset_n_scc_clk),

                .reset_n_avl_clk                        (reset_n_avl_clk),

                .read_capture_clk                       (read_capture_clk),

                .pll_locked                                     (pll_locked),

                .global_reset_n                         (global_reset_n),

                .soft_reset_n                           (soft_reset_n),

                .ctl_reset_export_n         (ctl_reset_export_n),

                .reset_n_afi_clk                        (reset_n_afi_clk),

                .reset_n_addr_cmd_clk           (reset_n_addr_cmd_clk),

                .reset_n_seq_clk                        (reset_n_seq_clk),

                .reset_n_resync_clk                     (reset_n_resync_clk)

        );

        defparam ureset.MEM_READ_DQS_WIDTH = MEM_READ_DQS_WIDTH;

        defparam ureset.NUM_AFI_RESET = NUM_AFI_RESET;

end else begin

        // synthesis translate_off

        hps_sdram_p0_reset      ureset(

                .pll_afi_clk                            (pll_afi_clk),

                .pll_addr_cmd_clk                       (pll_addr_cmd_clk),

                .pll_dqs_ena_clk                        (pll_dqs_ena_clk),

                .seq_clk                                        (seq_clk),

                .pll_avl_clk                            (pll_avl_clk),

                .scc_clk                                        (pll_config_clk),

                .reset_n_scc_clk                        (reset_n_scc_clk),

                .reset_n_avl_clk                        (reset_n_avl_clk),

                .read_capture_clk                       (read_capture_clk),

                .pll_locked                                     (pll_locked),

                .global_reset_n                         (global_reset_n),

                .soft_reset_n                           (soft_reset_n),

                .ctl_reset_export_n         (ctl_reset_export_n),

                .reset_n_afi_clk                        (reset_n_afi_clk),

                .reset_n_addr_cmd_clk           (reset_n_addr_cmd_clk),

                .reset_n_seq_clk                        (reset_n_seq_clk),

                .reset_n_resync_clk                     (reset_n_resync_clk)

        );

        defparam ureset.MEM_READ_DQS_WIDTH = MEM_READ_DQS_WIDTH;

        defparam ureset.NUM_AFI_RESET = NUM_AFI_RESET;

        // synthesis translate_on

        // synthesis read_comments_as_HDL on

        // assign reset_n_afi_clk = {NUM_AFI_RESET{global_reset_n}};

        // assign reset_n_addr_cmd_clk = global_reset_n;

        // assign reset_n_avl_clk = global_reset_n;

        // assign reset_n_scc_clk = global_reset_n;

        // synthesis read_comments_as_HDL off

end

endgenerate

assign phy_clk = seq_clk;

assign phy_reset_n = reset_n_seq_clk;

assign dll_clk = pll_write_clk_pre_phy_clk;

assign dll_pll_locked = pll_locked;

// PHY clock and LDC

wire afi_clk;

wire avl_clk;

wire adc_clk;

wire adc_clk_cps;

hps_sdram_p0_acv_ldc # (

        .DLL_DELAY_CTRL_WIDTH (DLL_DELAY_CTRL_WIDTH),

        .ADC_PHASE_SETTING (ADC_PHASE_SETTING),

        .ADC_INVERT_PHASE (ADC_INVERT_PHASE),

        .IS_HHP_HPS (IS_HHP_HPS)

) memphy_ldc (

        .pll_hr_clk (pll_avl_phy_clk),

        .pll_dq_clk (pll_write_clk),

        .pll_dqs_clk (pll_mem_phy_clk),

        .dll_phy_delayctrl (dll_phy_delayctrl),

        .afi_clk (afi_clk),

        .avl_clk (avl_clk),

        .adc_clk (adc_clk),

        .adc_clk_cps (adc_clk_cps)

);

assign ctl_clk = afi_clk;

assign afi_reset_n = reset_n_afi_clk;

// ******************************************************************************************************************************** 

// This is the hard PHY instance

// ******************************************************************************************************************************** 

        cyclonev_mem_phy hphy_inst (

                .pllaficlk                   (afi_clk),

                .pllavlclk                   (avl_clk),

                .plllocked                   (pll_locked),

                .plladdrcmdclk               (adc_clk),

                .globalresetn                (global_reset_n),

                .softresetn                  (soft_reset_n),

                .phyresetn                   (phy_reset_n),

                .ctlresetn                   (ctl_reset_n),

                .iointaddrdout               (io_intaddrdout),

                .iointbadout                 (io_intbadout),

                .iointcasndout               (io_intcasndout),

                .iointckdout                 (io_intckdout),

                .iointckedout                (io_intckedout),

                .iointckndout                (io_intckndout),

                .iointcsndout                (io_intcsndout),

                .iointdmdout                 (io_intdmdout),

                .iointdqdin                  (io_intdqdin),

                .iointdqdout                 (io_intdqdout),

                .iointdqoe                   (io_intdqoe),

                .iointdqsbdout               (io_intdqsbdout),

                .iointdqsboe                 (io_intdqsboe),

                .iointdqsdout                (io_intdqsdout),

                .iointdqslogicdqsena         (io_intdqslogicdqsena),

                .iointdqslogicfiforeset      (io_intdqslogicfiforeset),

                .iointdqslogicincrdataen     (io_intdqslogicincrdataen),

                .iointdqslogicincwrptr       (io_intdqslogicincwrptr),

                .iointdqslogicoct            (io_intdqslogicoct),

                .iointdqslogicrdatavalid     (io_intdqslogicrdatavalid),

                .iointdqslogicreadlatency    (io_intdqslogicreadlatency),

                .iointdqsoe                  (io_intdqsoe),

                .iointodtdout                (io_intodtdout),

                .iointrasndout               (io_intrasndout),

                .iointresetndout             (io_intresetndout),

                .iointwendout                (io_intwendout),

                .iointafirlat                (io_intafirlat),

                .iointafiwlat                (io_intafiwlat),

                .iointaficalfail             (io_intaficalfail),

                .iointaficalsuccess          (io_intaficalsuccess),

                .ddiophydqdin                (ddio_phy_dqdin),

                .ddiophydqslogicrdatavalid   (ddio_phy_dqslogic_rdatavalid),

                .phyddioaddrdout             (phy_ddio_address),

                .phyddiobadout               (phy_ddio_bank),

                .phyddiocasndout             (phy_ddio_cas_n),

                .phyddiockdout               (phy_ddio_ck),

                .phyddiockedout              (phy_ddio_cke),

                .phyddiockndout              (),

                .phyddiocsndout              (phy_ddio_cs_n),

                .phyddiodmdout               (phy_ddio_dmdout),

                .phyddiodqdout               (phy_ddio_dqdout),

                .phyddiodqoe                 (phy_ddio_dqoe),

                .phyddiodqsbdout             (),

                .phyddiodqsboe               (phy_ddio_dqsb_oe),

                .phyddiodqslogicdqsena       (phy_ddio_dqslogic_dqsena),

                .phyddiodqslogicfiforeset    (phy_ddio_dqslogic_fiforeset),

                .phyddiodqslogicaclrpstamble (phy_ddio_dqslogic_aclr_pstamble),

                .phyddiodqslogicaclrfifoctrl (phy_ddio_dqslogic_aclr_fifoctrl),

                .phyddiodqslogicincrdataen   (phy_ddio_dqslogic_incrdataen),

                .phyddiodqslogicincwrptr     (phy_ddio_dqslogic_incwrptr),

                .phyddiodqslogicoct          (phy_ddio_dqslogic_oct),

                .phyddiodqslogicreadlatency  (phy_ddio_dqslogic_readlatency),

                .phyddiodqsoe                (phy_ddio_dqs_oe),

                .phyddiodqsdout              (phy_ddio_dqs_dout),

                .phyddioodtdout              (phy_ddio_odt),

                .phyddiorasndout             (phy_ddio_ras_n),

                .phyddioresetndout           (phy_ddio_reset_n),

                .phyddiowendout              (phy_ddio_we_n),

                .afiaddr                     (afi_addr),

                .afiba                       (afi_ba),

                .aficalfail                  (afi_cal_fail),

                .aficalsuccess               (afi_cal_success),

                .aficasn                     (afi_cas_n),

                .aficke                      (afi_cke),

                .aficsn                      (afi_cs_n),

                .afidm                       (afi_dm),

                .afidqsburst                 (afi_dqs_burst),

                .afimemclkdisable            (afi_mem_clk_disable),

                .afiodt                      (afi_odt),

                .afirasn                     (afi_ras_n),

                .afirdata                    (afi_rdata),

                .afirdataen                  (afi_rdata_en),

                .afirdataenfull              (afi_rdata_en_full),

                .afirdatavalid               (afi_rdata_valid),

                .afirlat                     (afi_rlat),

                .afirstn                     (afi_rst_n),

                .afiwdata                    (afi_wdata),

                .afiwdatavalid               (afi_wdata_valid),

                .afiwen                      (afi_we_n),

                .afiwlat                     (afi_wlat),

                .avladdress                  (avl_address),

                .avlread                     (avl_read),

                .avlreaddata                 (avl_readdata),

                .avlresetn                   (reset_n_avl_clk),

                .avlwaitrequest              (avl_waitrequest),

                .avlwrite                    (avl_write),

                .avlwritedata                (avl_writedata),

                .cfgaddlat                   (cfg_addlat),

                .cfgbankaddrwidth            (cfg_bankaddrwidth),

                .cfgcaswrlat                 (cfg_caswrlat),

                .cfgcoladdrwidth             (cfg_coladdrwidth),

                .cfgcsaddrwidth              (cfg_csaddrwidth),

                .cfgdevicewidth              (cfg_devicewidth),

                .cfgdramconfig               (cfg_dramconfig),

                .cfginterfacewidth           (cfg_interfacewidth),

                .cfgrowaddrwidth             (cfg_rowaddrwidth),

                .cfgtcl                      (cfg_tcl),

                .cfgtmrd                     (cfg_tmrd),

                .cfgtrefi                    (cfg_trefi),

                .cfgtrfc                     (cfg_trfc),

                .cfgtwr                      (cfg_twr),

                .scanen                      ()