URL
https://opencores.org/ocsvn/amber/amber/trunk
Subversion Repositories amber
[/] [amber/] [trunk/] [hw/] [vlog/] [system/] [timer_module.v] - Rev 63
Go to most recent revision | Compare with Previous | Blame | View Log
////////////////////////////////////////////////////////////////// // // // Timer Module // // // // This file is part of the Amber project // // http://www.opencores.org/project,amber // // // // Description // // Contains 3 configurable timers. Each timer can generate // // either one-shot or cyclical interrupts // // // // Author(s): // // - Conor Santifort, csantifort.amber@gmail.com // // // ////////////////////////////////////////////////////////////////// // // // Copyright (C) 2010 Authors and OPENCORES.ORG // // // // This source file may be used and distributed without // // restriction provided that this copyright statement is not // // removed from the file and that any derivative work contains // // the original copyright notice and the associated disclaimer. // // // // This source file is free software; you can redistribute it // // and/or modify it under the terms of the GNU Lesser General // // Public License as published by the Free Software Foundation; // // either version 2.1 of the License, or (at your option) any // // later version. // // // // This source is distributed in the hope that it will be // // useful, but WITHOUT ANY WARRANTY; without even the implied // // warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR // // PURPOSE. See the GNU Lesser General Public License for more // // details. // // // // You should have received a copy of the GNU Lesser General // // Public License along with this source; if not, download it // // from http://www.opencores.org/lgpl.shtml // // // ////////////////////////////////////////////////////////////////// `include "global_defines.v" module timer_module #( parameter WB_DWIDTH = 32, parameter WB_SWIDTH = 4 )( input i_clk, input [31:0] i_wb_adr, input [WB_SWIDTH-1:0] i_wb_sel, input i_wb_we, output [WB_DWIDTH-1:0] o_wb_dat, input [WB_DWIDTH-1:0] i_wb_dat, input i_wb_cyc, input i_wb_stb, output o_wb_ack, output o_wb_err, output [2:0] o_timer_int ); `include "register_addresses.v" // Wishbone registers reg [15:0] timer0_load_reg = 'd0; // initial count value reg [15:0] timer1_load_reg = 'd0; // initial count value reg [15:0] timer2_load_reg = 'd0; // initial count value reg [23:0] timer0_value_reg = 24'hffffff; // current count value reg [23:0] timer1_value_reg = 24'hffffff; // current count value reg [23:0] timer2_value_reg = 24'hffffff; // current count value reg [7:0] timer0_ctrl_reg = 'd0; // control bits reg [7:0] timer1_ctrl_reg = 'd0; // control bits reg [7:0] timer2_ctrl_reg = 'd0; // control bits reg timer0_int_reg = 'd0; // interrupt flag reg timer1_int_reg = 'd0; // interrupt flag reg timer2_int_reg = 'd0; // interrupt flag // Wishbone interface reg [31:0] wb_rdata32 = 'd0; wire wb_start_write; wire wb_start_read; reg wb_start_read_d1 = 'd0; wire [31:0] wb_wdata32; // ====================================================== // Wishbone Interface // ====================================================== // Can't start a write while a read is completing. The ack for the read cycle // needs to be sent first assign wb_start_write = i_wb_stb && i_wb_we && !wb_start_read_d1; assign wb_start_read = i_wb_stb && !i_wb_we && !o_wb_ack; always @( posedge i_clk ) wb_start_read_d1 <= wb_start_read; assign o_wb_err = 1'd0; assign o_wb_ack = i_wb_stb && ( wb_start_write || wb_start_read_d1 ); generate if (WB_DWIDTH == 128) begin : wb128 assign wb_wdata32 = i_wb_adr[3:2] == 2'd3 ? i_wb_dat[127:96] : i_wb_adr[3:2] == 2'd2 ? i_wb_dat[ 95:64] : i_wb_adr[3:2] == 2'd1 ? i_wb_dat[ 63:32] : i_wb_dat[ 31: 0] ; assign o_wb_dat = {4{wb_rdata32}}; end else begin : wb32 assign wb_wdata32 = i_wb_dat; assign o_wb_dat = wb_rdata32; end endgenerate // ======================================================== // Timer Interrupt Outputs // ======================================================== assign o_timer_int = { timer2_int_reg, timer1_int_reg, timer0_int_reg }; // ======================================================== // Register Writes // ======================================================== always @( posedge i_clk ) begin if ( wb_start_write ) case ( i_wb_adr[15:0] ) // write to timer control registers AMBER_TM_TIMER0_CTRL: timer0_ctrl_reg <= i_wb_dat[7:0]; AMBER_TM_TIMER1_CTRL: timer1_ctrl_reg <= i_wb_dat[7:0]; AMBER_TM_TIMER2_CTRL: timer2_ctrl_reg <= i_wb_dat[7:0]; endcase // ------------------------------- // Timer 0 // ------------------------------- if ( wb_start_write && i_wb_adr[15:0] == AMBER_TM_TIMER0_LOAD ) begin timer0_value_reg <= {i_wb_dat[15:0], 8'd0}; timer0_load_reg <= i_wb_dat[15:0]; end else if ( timer0_ctrl_reg[7] ) // Timer Enabled begin if ( timer0_value_reg == 24'd0 ) begin if ( timer0_ctrl_reg[6] ) // periodic timer0_value_reg <= {timer0_load_reg, 8'd0}; else timer0_value_reg <= 24'hffffff; end else case ( timer0_ctrl_reg[3:2] ) 2'b00: timer0_value_reg <= (timer0_value_reg & 24'hffff00) - 9'd256; 2'b01: timer0_value_reg <= (timer0_value_reg & 24'hfffff0) - 9'd16; 2'b10: timer0_value_reg <= timer0_value_reg - 1'd1; default: begin //synopsys translate_off `TB_ERROR_MESSAGE $write("unknown Timer Module Prescale Value %d for Timer 0", timer0_ctrl_reg[3:2]); //synopsys translate_on end endcase end // ------------------------------- // Timer 1 // ------------------------------- if ( wb_start_write && i_wb_adr[15:0] == AMBER_TM_TIMER1_LOAD ) begin timer1_value_reg <= {i_wb_dat[15:0], 8'd0}; timer1_load_reg <= i_wb_dat[15:0]; end else if ( timer1_ctrl_reg[7] ) // Timer Enabled begin if ( timer1_value_reg == 24'd0 ) begin if ( timer1_ctrl_reg[6] ) // periodic timer1_value_reg <= {timer1_load_reg, 8'd0}; else timer1_value_reg <= 24'hffffff; end else case ( timer1_ctrl_reg[3:2] ) 2'b00: timer1_value_reg <= (timer1_value_reg & 24'hffff00) - 9'd256; 2'b01: timer1_value_reg <= (timer1_value_reg & 24'hfffff0) - 9'd16; 2'b10: timer1_value_reg <= timer1_value_reg - 1'd1; default: begin //synopsys translate_off `TB_ERROR_MESSAGE $write("unknown Timer Module Prescale Value %d for Timer 1", timer1_ctrl_reg[3:2]); //synopsys translate_on end endcase end // ------------------------------- // Timer 2 // ------------------------------- if ( wb_start_write && i_wb_adr[15:0] == AMBER_TM_TIMER2_LOAD ) begin timer2_value_reg <= {i_wb_dat[15:0], 8'd0}; timer2_load_reg <= i_wb_dat[15:0]; end else if ( timer2_ctrl_reg[7] ) // Timer Enabled begin if ( timer2_value_reg == 24'd0 ) begin if ( timer2_ctrl_reg[6] ) // periodic timer2_value_reg <= {timer2_load_reg, 8'd0}; else timer2_value_reg <= 24'hffffff; end else case ( timer2_ctrl_reg[3:2] ) 2'b00: timer2_value_reg <= (timer2_value_reg & 24'hffff00) - 9'd256; 2'b01: timer2_value_reg <= (timer2_value_reg & 24'hfffff0) - 9'd16; 2'b10: timer2_value_reg <= timer2_value_reg - 1'd1; default: begin //synopsys translate_off `TB_ERROR_MESSAGE $write("unknown Timer Module Prescale Value %d for Timer 2", timer2_ctrl_reg[3:2]); //synopsys translate_on end endcase end // ------------------------------- // Timer generated Interrupt Flags // ------------------------------- if ( wb_start_write && i_wb_adr[15:0] == AMBER_TM_TIMER0_CLR ) timer0_int_reg <= 1'd0; else if ( timer0_value_reg == 24'd0 ) // stays asserted until cleared timer0_int_reg <= 1'd1; if ( wb_start_write && i_wb_adr[15:0] == AMBER_TM_TIMER1_CLR) timer1_int_reg <= 1'd0; else if ( timer1_value_reg == 24'd0 ) // stays asserted until cleared timer1_int_reg <= 1'd1; if ( wb_start_write && i_wb_adr[15:0] == AMBER_TM_TIMER2_CLR) timer2_int_reg <= 1'd0; else if ( timer2_value_reg == 24'd0 ) // stays asserted until cleared timer2_int_reg <= 1'd1; end // ======================================================== // Register Reads // ======================================================== always @( posedge i_clk ) if ( wb_start_read ) case ( i_wb_adr[15:0] ) AMBER_TM_TIMER0_LOAD: wb_rdata32 <= {16'd0, timer0_load_reg}; AMBER_TM_TIMER1_LOAD: wb_rdata32 <= {16'd0, timer1_load_reg}; AMBER_TM_TIMER2_LOAD: wb_rdata32 <= {16'd0, timer2_load_reg}; AMBER_TM_TIMER0_CTRL: wb_rdata32 <= {24'd0, timer0_ctrl_reg[7:6], 2'd0, timer0_ctrl_reg[3:2], 2'd0 }; AMBER_TM_TIMER1_CTRL: wb_rdata32 <= {24'd0, timer1_ctrl_reg[7:6], 2'd0, timer1_ctrl_reg[3:2], 2'd0 }; AMBER_TM_TIMER2_CTRL: wb_rdata32 <= {24'd0, timer2_ctrl_reg[7:6], 2'd0, timer2_ctrl_reg[3:2], 2'd0 }; AMBER_TM_TIMER0_VALUE: wb_rdata32 <= {16'd0, timer0_value_reg[23:8]}; AMBER_TM_TIMER1_VALUE: wb_rdata32 <= {16'd0, timer1_value_reg[23:8]}; AMBER_TM_TIMER2_VALUE: wb_rdata32 <= {16'd0, timer2_value_reg[23:8]}; default: wb_rdata32 <= 32'h66778899; endcase // ======================================================================================= // ======================================================================================= // ======================================================================================= // Non-synthesizable debug code // ======================================================================================= //synopsys translate_off `ifdef AMBER_CT_DEBUG reg timer0_int_reg_d1; reg timer1_int_reg_d1; reg timer2_int_reg_d1; wire wb_read_ack = i_wb_stb && !i_wb_we && o_wb_ack; // ----------------------------------------------- // Report Timer Module Register accesses // ----------------------------------------------- always @(posedge i_clk) if ( wb_read_ack || wb_start_write ) begin `TB_DEBUG_MESSAGE if ( wb_start_write ) $write("Write 0x%08x to ", i_wb_dat); else $write("Read 0x%08x from ", o_wb_dat); case ( i_wb_adr[15:0] ) AMBER_TM_TIMER0_LOAD: $write(" Timer Module Timer 0 Load"); AMBER_TM_TIMER1_LOAD: $write(" Timer Module Timer 1 Load"); AMBER_TM_TIMER2_LOAD: $write(" Timer Module Timer 2 Load"); AMBER_TM_TIMER0_CTRL: $write(" Timer Module Timer 0 Control"); AMBER_TM_TIMER1_CTRL: $write(" Timer Module Timer 1 Control"); AMBER_TM_TIMER2_CTRL: $write(" Timer Module Timer 2 Control"); AMBER_TM_TIMER0_VALUE: $write(" Timer Module Timer 0 Value"); AMBER_TM_TIMER1_VALUE: $write(" Timer Module Timer 1 Value"); AMBER_TM_TIMER2_VALUE: $write(" Timer Module Timer 2 Value"); AMBER_TM_TIMER0_CLR: $write(" Timer Module Timer 0 Clear"); AMBER_TM_TIMER1_CLR: $write(" Timer Module Timer 1 Clear"); AMBER_TM_TIMER2_CLR: $write(" Timer Module Timer 2 Clear"); default: begin $write(" unknown Amber IC Register region"); $write(", Address 0x%08h\n", i_wb_adr); `TB_ERROR_MESSAGE end endcase $write(", Address 0x%08h\n", i_wb_adr); end always @(posedge i_clk) begin timer0_int_reg_d1 <= timer0_int_reg; timer1_int_reg_d1 <= timer1_int_reg; timer2_int_reg_d1 <= timer2_int_reg; if ( timer0_int_reg && !timer0_int_reg_d1 ) begin `TB_DEBUG_MESSAGE $display("Timer Module Timer 0 Interrupt"); end if ( timer1_int_reg && !timer1_int_reg_d1 ) begin `TB_DEBUG_MESSAGE $display("Timer Module Timer 1 Interrupt"); end if ( timer2_int_reg && !timer2_int_reg_d1 ) begin `TB_DEBUG_MESSAGE $display("Timer Module Timer 2 Interrupt"); end end `endif //synopsys translate_on endmodule
Go to most recent revision | Compare with Previous | Blame | View Log